Two refrigerators carrying the same stated storage capacity can occupy different amounts of floor space. One may distribute its volume across a wider cabinet, while another uses greater height or depth. For a wholesale range, that difference affects which products can serve the intended locations even before their features are compared.
A purchasing shortlist therefore needs a sequence that starts with dimensional limits, organises the required categories, identifies individual models and defines the scope of the proposed wholesale supply order.
Set the Dimensional Limits
External measurements, storage volume and installation space describe three separate things. Width and depth establish the cabinet footprint, height defines its vertical extent, and litres express storage volume. The space reserved for operation and access extends the comparison beyond the closed appliance body. The measurement basis also matters where handles or other projections alter the external outline.
Selecting wholesale refrigerators by capacity alone can retain models whose proportions do not suit the intended setting. A wider cabinet may be unsuitable for one opening even where its listed volume matches that of a narrower alternative. Width, height and depth limits narrow the candidate group without assuming that a capacity figure predicts its shape.
Units also matter when comparing catalogue fields. A measurement expressed in centimetres needs conversion before it can be compared directly with a limit stated in millimetres. The dimension names and their order require equal attention, since width, depth and height describe different directions.
The resulting limits define the physical range of candidates. Category selection can then address the required balance between refrigerated and frozen storage within that range.
Assemble the Required Category Mix
A wholesale assortment can combine products serving different storage roles. A standalone freezer adds frozen capacity independently of the refrigerated section, while a combination appliance brings both functions into one cabinet.
Dimensional limits may admit both formats, leaving the balance of fresh and frozen storage to determine their place in the range. The mix depends on the capacity allocated to each function and the locations where those products will be used, rather than a preference for the largest cabinet.
The twelve-category catalogue from Homa Appliances spans combined refrigerator-freezers, upright formats, chest freezers and built-in options. Those groups provide starting points for a selection, with further distinctions covering cooling arrangements and installation styles. A programme can draw from more than one group where its proposed range serves different locations or storage requirements.
Comparing wholesale refrigerators within a category keeps the product role reasonably consistent while dimensions and configurations are examined. Comparing across categories answers a different question about the composition of the overall assortment. A category identifies a candidate family; it leaves the exact model and its specification to be established.
Keep Model Codes beside Their Specifications
A similar prefix or number sequence does not establish a product’s dimensions or capacity. Model codes distinguish catalogue entries, but the specification fields carry the measurements needed for comparison. FN2-65 and FF4-54 are examples of individual model references within the company’s catalogue.
Each candidate needs its own row of information. The code remains beside the stated width, height, depth and capacity, together with the relevant category and configuration. Separate fields for total volume and compartment allocation also distinguish products with otherwise similar headline descriptions. That arrangement separates identity from measurement instead of interpreting the digits in a model name as litres or millimetres.
A shortlist of wholesale refrigerators becomes more specific as these fields are completed. Two entries may satisfy the same dimensional limits yet allocate their storage differently or belong to different installation groups. The comparison then concerns the stated characteristics of the actual candidates, rather than resemblance between their names.
Hyphens and digits are part of the reference and need to remain intact. A clearly identified candidate can move into an order discussion with its selected configuration attached.
Define the Product and Order Scope
Choosing an existing model and requesting a configuration change begin different commercial discussions. The first identifies a product from the available range; the second adds development requirements to that starting point. Quantity and the nature of any requested alteration therefore need separate descriptions.
Homa’s overseas business is mainly ODM, and customisation applies to large-volume orders. A proposed adjustment belongs with the model or product brief to which it relates. The required quantity does not, by itself, describe what has to change in the appliance.
For wholesale refrigerators, an order comparison can keep the candidate model, selected configuration and quantity together while recording requested changes separately. That distinction preserves a clear basis for discussing existing products and customised projects.
Separate quantities for each candidate prevent a combined order total from concealing differences in the products actually being requested. The purchasing requirement becomes a defined combination of products and quantities, with the intended development scope stated explicitly.
Matching capacity figures can lead to different purchasing choices once cabinet proportions, category roles and individual specifications are considered. Dimensional limits first establish what can occupy the intended space, while the model reference preserves the identity of each remaining candidate. Category and configuration details explain its place within the assortment. A shortlist carrying those fields alongside quantities and requested changes gives subsequent quotations a common product and order basis for comparison between the candidate models.